Filter Project 13 Ft (4 meter) Automatic Self Cleaning Dry Granite
Dust Collector is made to trap 99% of Dust from Granite, Marble,
Engineered Stone, Quartz, Quartzite, Fiberglass, Ceramic, Porcelain,
and other airborne particles
Filter Project 13 ft (4 meter) Dry Dust Collection Booths are
all stainless steel, heavy duty, dry dust collectors made to
eliminate 99.99% of dust particles.
With the additional requirements initiated by OSHA for Silica in the
granite and engineered stone, the Filter
Project Clean Air Dry Dust Collection Booths will be a major
advantage in removing silica dust from the air. Filter Project
Automatic Dry Dust Collectors vacuum air from the bottom of the
unit. That means that the air flow is coming from below the knees,
creating a downward pull of air. The major advantage of this air
flow movement is that the dust is pulled down from the work table
immediately away from the face. This design is the absolute best way
to reduce as much dust from the workers as fast as possible.
The operation of the Dry Dust Collector is extremely simple. Simply
push the button and work in front of it. The dust will be vacuumed
horizontally into the dry dust collector without the fabricator
breathing any of the dust.
How do the Automatic Dry Dust Collection Booths Work?
Project Dry Dust Collectors have specially designed cloth
filtering sleeves inside the Dry Dust Collector. When turned on the
Dry Dust Suction Walls very powerful motors create a strong vacuum
that pulls the dust particles horizontally from the work bench area
and then pulls it down to the bottom of the wall and inside the
unit. Inside the dust collector the many cloth filtering sleeves
trap the dust and captures 99.99% of the dust. Only clean filtered
air comes out the top of the Dry Dust Cabin.
The dust is then collected in the catch basin drawer at the bottom
of the dryd ust collection booth. Every day or once a week,
depending on use, simply empty the dust that has been collected in
the bottom of the catch basin.
Project Dry Dust Collection Booth comes with a 3 ft (1 meter)
extension enclosure that provides additional dust control and
greater vacuum efficiency. 6 ft (2 meter) extension enclosures are
available as options
Dry Dust Collectors in Automatic Self Clean mode: a self-cleaning
system with compressed air, made by a pressurized tank, and a series
of membrane electrovalves with specific blowing tubes are inside the
cloth filter sleeves and controlled by an automatic sequencer. That
means that the unit is self cleaning. Once the Dry Dust Collector is
turned off, the system will automatically go through an air cleaning
cycle to blow the dust out of the sleeves and the dust will settle
at the bottom inside the dust drawers.
Filter Project Dry Dust Collection Booths are available in other
sizes in both Manual Dust Collection and Automatic Dust collection:
Automatic Dry Dust Collector
6 1/2 ft (2 meter) Automatic Cleaning Dry Dust Collection Booth.
10 ft (3 meter) Automatic Cleaning Dry Dust Collection Booth.
Designed to trap 99% of Granite Dust, Marble Dust, Engineered Stone
Dust, Quartz Dust, Concrete Dust, Natural Stone Dust, and other fine
airborne particles. These dust collectors are the best way to remove
granite dust, quartz, dust, marble dust, out of a fab shop.
These units are the best dust collection systems for stone
fabrication and removing granite dust, marble dust, quartz, and
engineered stone dust out of the environment.
Dry Dust Collector Electrical Requirements:
220 (208) 3 Phase Power
30 Amp Breaker
Also required is a 90 PSI, minimum 2 CFM air connection
Filter Project Granite and Stone Dust Collection Dry
Wall Replacement Sleeves:
Filter Project Granite and Stone Automatic Dry Dust
Collectors come with a complete set of Dust Sleeves already
installed on the dry dust collectors.
Once the dust collector sleeves are worn out they
will need to be replaced.
Filter Project Automatic Dry Dust Collectors make it
very simple and easy to change the bags. Simply loosen the clamp and
slide them off. Watch the video below to see how to change out the
Maintenance of the Dry Dust Collector Filter Sleeves:
After 6 months to a 1 year, remove the sleeves, blow
them out, and wash them with water. Let them dry and reinstall them.
When the Dry Dust Collector starts loosing vacuum power, it will be
time to change out the Sleeves.
Filter Project Dry Dust Collector Booths can be used for all types
of airborne particle:
Granite Dust Collection
Marble Dust Collection
Quartz Dust Collection
Quartzite Dust Collection
Concrete Dust Collection
Cultured Marble Dust Collection
Fiberglass Dust Collection
Porcelain Dust Collection
Below is the number of Dry Dust Collector Sleeves
required per Dust Collector:
6 Ft (2 meter) Dry Dust Collector: 36 Sleeves
10 Ft (3 meter) Dry Dust Collector: 52 Sleeves
13 Ft (4 meter) Dry Dust Collector: 72 Sleeves